He takes JOY in sharing product knowledge with others. He is passionate about sharing knowledge and also to seamlessly collaborate with SAP SF community members. Long term vision is to use the seed capital for CHARITY purpose. Here’s looking forward to everyone's wishes and support in this initiative. Happy Blogging:)
Sunday, September 15, 2019
Friday, September 6, 2019
accessing #CSB from Admin Center the page will not load or the user is sent back to the home page.
2826067 - Career Site Builder is not Accessible After the preview Release - Recruiting Marketing
Thursday, September 5, 2019
Recruiting Integrations#RMK#General Troubleshooting #Provisioning#Security Key#Recruiter Sync#Real Time Job Sync
Check
these Settings – 1
ŸFirst, clear your browser’s cache
or try again with a different browser. Then carefully check the steps in the
exercise and the proceeding ones, especially the settings listed below.
ŸCommand Center
ŸSite > Site Setup*
ŸIntegrations > Manage API Credentials
ŸNote that some students using their
partner company’s shared stage instance have found their Command settings
changed, but not by them. Check for that!
ŸFor example, one student was not able to
apply for a job and found that her page rules had disappeared from the shared
Stage site
Ÿ
*
Getting the “HTTP Status 500” error? Confirm that you have enabled Site >
Site Setup > Settings > Use Career Site Builder. Also confirm that your
user is set up for Recruiter SSO.
--------------------------------------------------------------------------------------------------Check these Settings – 2
ŸProvisioning
ŸCompany Settings > Enable Social
Sourcing > Recruiting Marketing > Enable Job Marketing & Enable
Career Site Builder
ŸService Provider Settings > Recruiting
Marketing Settings
ŸThe Company Settings referenced in the
Recruiter SSO exercise
ŸFor example, if you click Apply and are
redirected back to the job page, ensure that you have disabled Enable E-Mail
Verification for Career Site
ŸAdmin Center
ŸRole-based permissions (see each
exercise)
---------------------------Troubleshooting Tips – Security Key
ŸIf the Security Key is not set
correctly, several types of errors can occur:
ŸRecruiter SSO
ŸReal-time Job Sync
ŸWhen attempting to open CSB you are
redirected back to the instance home page.
ŸEnsure that the Security Key
follows the rules:
ŸFrom 20-28 characters
ŸAt least one upper and one lower case
letter
ŸAt least one numeric character
ŸAt least one special
character/punctuation
ŸEnsure that the Security Key is the
same in Command Center > Site Setup > SSO and in Provisioning >
Service Provider Settings > Recruiting Marketing Settings. (For security
reasons, the Key will be cleared after saving each time.)
ŸEnsure that the Security Key is
unique (not used in another instance).
-------------------------
Troubleshooting
Tips – Recruiter Sync
ŸThere may be a delay to see your
results.
ŸIf the recruiters do not appear in
Command Center under Users > Search (Client Admin), check that each has a
unique email address. (The most common error.)
ŸEnsure that your Staffing Group is
populated in Admin Center.
ŸTo see the status of your job,
check the logs from Command Center > Site > Site Maintenance Viewer and
click on Load Prior 24h Data. Select the job and read the log at the bottom.
ŸIf the log shows a 403 Error, check
the System Name field on the SSO page and ensure that you’ve selected the
datacenter where your instance is installed.
ŸCheck the settings from Site Setup
> SSO and re-run Recruiter Sync.
ŸIf when you click Manage Career
Site Builder you get the error “The requested operation is not available” check
that your admin user (HR Admin) is included in the Recruiter Sync.
ŸSome students have reported that
Recruiter Sync wouldn’t run for them, but it worked when the instructor ran it
from the student’s Command Center instance.
--------------------
Troubleshooting
Tips – Real Time Job Sync
ŸThere may be a delay to see your
results. Even if a scheduled job in Provisioning is displayed as Complete, the
job may not be finished running on the RMK side. The request is sent to a queue
called “Maintenance” and the time to execute maintenance jobs varies greatly
based on the time of day and number of jobs in queue.
ŸTo see if the job was run by RMK,
check the logs from Command Center > Site > Site Maintenance Viewer and
click on Load Prior 24h Data. Select the job and read the log at the bottom.
ŸConfirm that every job contains a
job description.
ŸConfirm that the jobs are posted to
the external career site created for RCM.
ŸUn-post and re-post the job in RCM.
Also change a field on the requisition and save the change.
ŸEnsure that you have not included a
large image in the job requisition that exceeds the size limit.
ŸCheck your field mapping.
ŸRe-run the Recruiting Marketing
“Sync all external job postings” job in Provisioning.
ŸCheck your settings in Provisioning
for the RMK Service Provider Settings (including the Security Key) and the RMK
Datacenter URLs.
ŸIf used, ensure that a Job Profile
exists for that particular requisition. One customer's job would not sync
because of invisible characters in empty lines in the Job profile, External job
description.
Credits:KSmall
Wednesday, September 4, 2019
Subscribe to:
Posts (Atom)